Three-Phase DC Power Supply RPL 2410WD-2440D
Single-phase DC power supplyRPL 122.5W – 2440WRegulated primary-switched single-phase switching power suppliesAvailable in 30W, 60W, 125W, 250W, 480W and 960WInput wide input voltage range 85-264V, 90-264V, 196-460V (depending on version) see data sheetOutput DC 12, 24 or 48V General:Primary-switched power supplies do not require a mains transformer, are compact and lightweight.Special features of the RPL series Universal input (AC or DC for single-phase or 3AC or DC for three-phase devices) with wide input voltage range Output voltage adjustable over a wide range via front-side potentiometer Power supplies of the RPL series can be used as chargers (type …WL) By simply repositioning the jumper on 250W alternating current, 480W alternating current and 480W three-phase current or by implementing the –T option on other chargers in conjunction with the installation of a temperature sensor (NTC resistor 10kΩ) on the battery, temperature-controlled charging of the batteries is activated. This leads to optimized charging of the batteries in the event of large fluctuations in ambient temperature and increases, among other things, the life expectancy of the battery Can be connected in series and parallel 25% power boost for 4s in the event of occurring peak loads Protection against overload, short circuit, overvoltage and overtemperature Three-color status LED, on devices from 125W: green – voltage stabilization, red - current limiting, yellow – device on mains, output voltage switched off Potential-free fault signaling contact (changeover contact)Options: -S: Decoupling diode (series diode) at the output for easy setup of redundancy and UPS systems; -U: Analog input DC 0-10V for adjusting the output voltage from 0 to Uout max; -D: Overload Shut Down, latching shutdown in case of overload; -P: symmetrical power distribution in parallel operation; -T: Temperature-controlled charging; -F: Remote off/on switching; -A: Fault signaling contact (alarm); -M: Minus temperature range. Is only relevant for RPL 2440D, since other devices are designed as standard for minus temperature range; -C: Mains harmonic limitation according to EN 61000-3-2 Class C (lighting systems).
Available immediately
Three-Phase DC Power Supply RSNT 20-60 G
THREE-PHASE DC POWER SUPPLYRSNT 20 – 60 GSecondary-switched three-phase switching power supplies, 20–60 A, regulatedInput 3AC 400 V,Output: DC 24 V, stabilized, dual-channel, adjustable,Adjustable output current General:The RSNT 20–60 G series switching power supplies are designed with a three-phase isolating transformer and a downstream switching regulator. The permissible interference level limits according to VDE 0875 Part 11 and EN 55011 Limit Curve B are significantly undershot.The extremely low noise level was achieved through a circuit design developed by us and protected by patent. Filtering and shielding measures are completely unnecessary.The switching power supplies are overload- and short-circuit-proof and can be connected in parallel without restriction.Internal electronic protection ensures that the devices always operate within the safe operating area (SOA protection).Two LEDs indicate the current operating status: green for constant-voltage operation and yellow for constant-current operation.Configuration:Sturdy sheet steel housing with integrated mounting holes, for device installation and mounting in dry rooms,Primary and secondary connections and PE via external, creepage-current-proof terminal blocks with screw terminals. The terminal blocks are protected against contact by the back of the hand and fingers in accordance with UVV (BGV A3).Maximum secondary voltage: DC 0...60 V.Devices can be combined as master/slave units in any configuration (Umax = DC 200 V)
Delivery time on requestk
Single-phase DC power supply RNTU 24S–240S 230V
Single-phase DC power supplyRNTU 24S - 240SSingle-phase compact unregulated power suppliesInput AC 230V or AC 400VOutput DC 24V or DC 12V, residual ripple < 5%.also available with various primary voltages up to max. AC 400V and secondary voltages from DC 10V to DC 60V. Featuring a compact and space-saving design in modern industrial styling, the power supplies of the RNTU series offer comprehensive protection against accidental contact thanks to their enclosed construction. The power supplies meet the requirements for protection against hazardous body currents according to VDE 0106 Part 101 and can be modularly snapped onto a mounting rail simply and quickly, from DC 5A additionally screwed.Devices of the same type can be connected in parallel at max. 90% load per device. The built-in fuses (see table) serve exclusively for short-circuit protection and ensure safe operation even under worst-case conditions. The devices may only be loaded with the specified rated current. Short-term drops in the mains voltage are bridged by generously dimensioned capacitors.In addition to the specifications listed below, the RNTU series is also available in various primary voltages up to max. AC 400V and secondary voltages from DC 10V to DC 60V at extra charge. However, the specified currents must not be exceeded.
Delivery time on requestk
Single-phase DC power supply RPL 122.5W – 2440W
Single-phase DC power supplyRPL 122.5W – 2440WRegulated primary-switched single-phase switching power suppliesAvailable in 30W, 60W, 125W, 250W, 480W, and 960WInput: Wide input voltage range 85–264 V, 90–264 V, 196–460 V (depending on model); see data sheetDC 12, 24, or 48V output General:Primary-switched power supplies do not require a line transformer; they are compact and lightweight.Special Features of the RPL Series Universal input (AC or DC for single-phase devices; 3AC or DC for three-phase devices) with a wide input voltage range Output voltage adjustable over a wide range via a front-panel potentiometer Power supplies from the RPL series can be used as chargers (Type …WL) By simply repositioning the jumper for 250W AC, 480W AC, and 480W three-phase AC—or by enabling the –T option on other chargers in conjunction with installing a temperature sensor (10kΩ NTC resistor) on the battery—temperature-controlled charging of the batteries is activated. This results in optimized battery charging even with large fluctuations in ambient temperature and, among other benefits, increases the battery’s service life. Can be connected in series or in parallel 25% power boost for 4 seconds during peak loads Protection against overload, short circuit, overvoltage, and overtemperature Three-color status LED, for devices 125W and above: green – Voltage stabilization, red - Current limiting, Yellow – Device connected to the mains, output voltage disabled Dry contact fault signal (changeover contact)Options: -S: Decoupling diode (series diode) at the output for easy configuration of redundancy and UPS systems; -U: Analog input DC 0–10 V for adjusting the output voltage from 0 to Uout max; -D: Overload Shut Down, memory-based shutdown in case of overload; -P: Symmetrical power distribution in parallel operation; -T: Temperature-controlled charging; -F: Remote on/off switching; -A: Fault signal contact (alarm); -M: Sub-zero temperature range. This applies only to the RPL 2440D, as other devices are designed for sub-zero temperatures as standard; -C: Mains harmonic suppression in accordance with EN 61000-3-2 Class C (lighting systems).
Delivery time on requestk
Single-phase DC power supply REP1-2405-2425 115/230V
Single-phase DC power supplyREP1 72 – REP3 600Regulated primary-switched single-phase switching power suppliesAvailable in 40–70W, 95–120W, 120–180W, 240–336W, and 480–600WInput: Wide input voltage range: AC 90–264 V, AC 90–135 V and 180–264 V, AC 187–264 V and 330–550 V, 3AC 330–550 V (depending on model)—see data sheetOutput: DC 12, 24, or 48V (depending on version); see datasheet General:The REP power supplies are high-quality switching power supplies for DIN rail mounting. They stand out thanks to their compact and intelligent design as well as their robust metal housing.The output voltage is easily and simply adjustable (DC 22V to DC 27V) and remains highly stable even with temperature fluctuations and load changes. In addition to short-circuit protection with 3 different output protection modes, overload and overvoltage protection at the output ensure a high level of safety.Special Features of the REP Series The output power can be easily increased by connecting additional REP power supplies of the same type in parallel (max. 4 units for the 280–500 W version) Series connection possible up to DC 110V 1.5 times the rated current for 3 min. 3 times the rated current for 300 ms.Alternatives:The REP series devices are also available in DC 12V as typeREP1-1206 (Secondary DC 12V/6A) Part No.: 0540-00001206REP1-1214 (Secondary DC 12V/14A) Part No.: 0540-00001214The devices in the REP series are also available in a 48V DC version as typeREP1-483.75 (Secondary DC 48V/3.75A) Part No.: 0540-00483.75REP1-4807 (Secondary DC 48V/7A) Part No.: 0540-00004807REP1-4812.5 (Secondary DC 48V/12.5A) Part No.: 0540-00004812.5No UL certification for DC 12V and DC 48V versionsFor more information, see www.riedel-trafobau.de
Delivery time on requestk
Three-phase DC power supply RDRKN 10-60 (K)
THREE-PHASE DC POWER SUPPLYRDRKN 10 – 60Three-phase compact rectifier transformersStandard version:Three-phase isolating transformer with a downstream three-phase bridge rectifier,Input 3AC 380/400/420 VOutput: 24 V DC, residual ripple < 5%Capacitor design:Three-phase isolating transformer with a downstream three-phase bridge rectifier and capacitorInput 3AC 380/400/420 VOutput: 24 V DC, residual ripple < 2% Configuration:Enclosed design, stationary, for equipment installation and mounting in dry rooms, with separate windings. Connection to transformer terminals protected against leakage current with screw terminals. The terminals are protected against contact by the back of the hand and fingers in accordance with UVV (BGV A3).IP 00, insulation class E, max. ambient temperature 40°C (ta40°C/E). Insulation class E
Delivery time on requestk
Single-phase DC power supply RNTG 12S - 120S 230V
Single-phase DC power supplyRNTG 12S - 120SRegulated single-phase compact power suppliesInput AC 230VOutput DC 24V, residual ripple < 2 mV rms..also available in various primary voltages up to max. AC 400V and secondary voltages from DC 5V to DC 30V. High-precision discretely constructed series regulator, finely adjustable.The power supplies of the RNTG series, compactly and space-savingly designed in modern industrial design, offer comprehensive protection against accidental contact due to the enclosed construction. The power supplies meet the requirements for protection against hazardous body currents according to VDE 0106 Part 101 and can be simply and quickly snapped onto a mounting rail in modular fashion, from DC 5A additionally screwed.Devices of the same type can be connected in parallel at max. 80% utilization per device.The built-in fuses (see table) serve exclusively for short-circuit protection and ensure safe operation even under worst-case conditions. The devices may only be loaded with the specified rated current. Short-term drops in the mains voltages are bridged up to 10ms during rated operation.The RNTG series is available, in addition to the specifications listed below, also in various primary voltages up to max. AC 400V and secondary voltages from DC 5V to DC 30V for an additional charge. However, the specified currents must not be exceeded.
Delivery time on requestk
Single-phase DC power supply GGTN 72 – 360 230/400V
Single-phase DC power supplyGGTN 72 – 360Single-phase compact rectifier transformersInput AC 220/400 VOutput: 24 V DC, residual ripple < 5%. New series with higher current with downstream rectifier, varistor, capacitor, protective circuit, and discharge resistor Residual ripple < 5% Status indicator LED Flat-plug fuse DIN 72581/3C Complies with the EN 61000-3-2 harmonic standard. IP 00, insulation class E Max. ambient temperature ta 40°C, insulation class E
Delivery time on requestk
Single-phase DC power supply REP2-2405-2414 230/400/500V
Single-phase DC power supplyREP1 72 – REP3 600Regulated primary-switched single-phase switching power suppliesavailable in 40-70W, 95-120W, 120-180W, 240-336W and 480-600WInput wide input voltage range AC 90-264V, AC 90-135V and 180-264V, AC 187-264V and 330-550V, 3AC 330-550V (depending on version) see data sheetOutput DC 12, 24 or 48V (depending on version) see data sheet General:The REP power supplies are high-quality switching power supplies for DIN rail mounting. They stand out thanks to their compact and intelligent design as well as their robust metal housing.The output voltage is easily and simply adjustable (DC 22V to DC 27V) and remains highly stable even with temperature fluctuations and load changes. In addition to short-circuit protection with 3 different output protection modes, overload and overvoltage protection at the output ensure a high level of safety.Special features of the REP series The output power can be easily increased by connecting additional REP power supplies of the same type in parallel (max. 4 units/280-500W version) Series connection possible up to DC 110V 1.5 times the rated current for 3min. 3 times the rated current for 300ms.Alternatives:The devices of the REP series are also available in DC 12V as typeREP1-1206 (Secondary DC 12V/6A) Part No.: 0540-00001206REP1-1214 (Secondary DC 12V/14A) Part No.: 0540-00001214The devices of the REP series are also available in DC 48V as typeREP1-483.75 (Secondary DC 48V/3.75A) Part No.: 0540-00483.75REP1-4807 (Secondary DC 48V/7A) Part No.: 0540-00004807REP1-4812.5 (Secondary DC 48V/12.5A) Part No.: 0540-00004812.5No UL certification for DC 12V and DC 48V versionsFor more information see www.riedel-trafobau.de
Delivery time on requestk
Single-phase DC power supply REP3-2425 3AC400 ... 500 V
Single-phase DC power supplyREP1 72 – REP3 600Regulated primary-switched single-phase switching power suppliesAvailable in 40–70W, 95–120W, 120–180W, 240–336W, and 480–600WInput: Wide input voltage range: AC 90–264 V, AC 90–135 V and 180–264 V, AC 187–264 V and 330–550 V, 3AC 330–550 V (depending on model)—see data sheetOutput: DC 12, 24, or 48V (depending on version); see datasheet General:The REP power supplies are high-quality switching power supplies for DIN rail mounting. They stand out thanks to their compact and intelligent design as well as their robust metal housing.The output voltage is easily and simply adjustable (DC 22V to DC 27V) and remains highly stable even with temperature fluctuations and load changes. In addition to short-circuit protection with 3 different output protection modes, overload and overvoltage protection at the output ensure a high level of safety.Special Features of the REP Series The output power can be easily increased by connecting additional REP power supplies of the same type in parallel (max. 4 units for the 280–500 W version) Series connection possible up to DC 110V 1.5 times the rated current for 3 min. 3 times the rated current for 300 ms.Alternatives:The REP series devices are also available in DC 12V as typeREP1-1206 (Secondary DC 12V/6A) Part No.: 0540-00001206REP1-1214 (Secondary DC 12V/14A) Part No.: 0540-00001214The devices in the REP series are also available in a 48V DC version as typeREP1-483.75 (Secondary DC 48V/3.75A) Part No.: 0540-00483.75REP1-4807 (Secondary DC 48V/7A) Part No.: 0540-00004807REP1-4812.5 (Secondary DC 48V/12.5A) Part No.: 0540-00004812.5No UL certification for DC 12V and DC 48V versionsFor more information, see www.riedel-trafobau.de
Delivery time on requestk
Single-phase DC power supply GGT 100–630 400V
Single-phase DC power supplyGGT 100 – 630Single-phase compact rectifier transformersInput AC 220/230/240V or AC 380/400/420VOutput DC 24V, residual ripple 48%. New series with higher current with downstream rectifier, varistor, and discharge resistor Residual ripple 48%, retrofitting a capacitor is not possible. Same design as above. The EN 61000-3-2 harmonic standard is complied with. IP 00, suitable for installation up to protection class IP 23, insulation class E, max. ambient temp. ta 40°C insulation class E
Delivery time on requestk
Three-phase DC power supply RDRK 2.5–60 (K)
THREE-PHASE DC POWER SUPPLYRDRK 2.5 – 60Three-phase compact rectifier transformersStandard version:with a downstream three-phase bridge rectifier,Input 3AC 380/400/420V, output DC 24V, residual ripple < 5%Capacitor design:with a downstream three-phase bridge rectifier and capacitorInput 3AC 380/400/420V, output DC 24V, residual ripple < 2% General:The RDRK series has been specifically developed for use with programmable logic controllers (PLCs). The transformers are very well-sized and voltage-stable. This results in a particularly flat characteristic curve between no-load and load conditions, ensuring that overvoltages or undervoltages critical for PLCs do not occur, even during significant mains fluctuations.The rectifiers are protected against short-term current surges and voltage spikes.The protective circuitry for the capacitor version is provided by a protection board containing the corresponding varistor, film capacitor, and discharge resistor.Configuration:Open, upright design, stationary, for equipment installation and mounting in dry rooms, isolated windings, all connections via creepage-current-proof screw terminal blocks. The terminals are protected against contact by the back of the hand and fingers in accordance with UVV (BGV A3).IP 00, insulation class E, max. ambient temperature 40°C (ta40°C/E)For versions with a capacitor, the dimensions change slightly. The mounting dimensions remain unchanged.Other versions available upon request (fuses, voltages, connections, etc.) Insulation class E
Delivery time on requestk
Three-phase DC power supply RDRKU 5-25
THREE-PHASE DC POWER SUPPLYRDRKU 5 – 25Three-Phase Universal Compact Rectifier Transformerswith a downstream three-phase bridge rectifier and capacitorInput voltage selectable: 3AC 210/220/230/240/255/265/275/290/300/360/380/400/420/440/460/480/500/520 VOutput: 24 V DC, residual ripple < 2% Configuration:Open design, stationary, for equipment installation and mounting in dry rooms, separate windings. Connection to transformers with creepage current protection via screw terminals and flat plug connections: 2.8 x 0.8 mm up to 5 A, 6.3 x 0.8 mm up to 20 A. According to DIN 46249, the 2.8 x 0.8 mm flat plug connection may only be loaded up to 5 A, and the 6.3 x 0.8 mm connection up to 20 A. The terminals are protected against contact by the back of the hand and fingers in accordance with UVV (BGV A3).IP 00, insulation class E, max. ambient temperature 40°C (ta40°C/E). Insulation class E
Delivery time on requestk
Single-phase DC power supply RNTU 24S–240S 230V
Single-phase DC power supplyRNTU 24S - 240SSingle-phase compact unregulated power suppliesInput AC 230V or AC 400VOutput DC 24V or DC 12V, residual ripple < 5%.also available with various primary voltages up to max. AC 400V and secondary voltages from DC 10V to DC 60V. Featuring a compact and space-saving design in modern industrial styling, the power supplies of the RNTU series offer comprehensive protection against accidental contact thanks to their enclosed construction. The power supplies meet the requirements for protection against hazardous body currents according to VDE 0106 Part 101 and can be modularly snapped onto a mounting rail simply and quickly, from DC 5A additionally screwed.Devices of the same type can be connected in parallel at max. 90% load per device. The built-in fuses (see table) serve exclusively for short-circuit protection and ensure safe operation even under worst-case conditions. The devices may only be loaded with the specified rated current. Short-term drops in the mains voltage are bridged by generously dimensioned capacitors.In addition to the specifications listed below, the RNTU series is also available in various primary voltages up to max. AC 400V and secondary voltages from DC 10V to DC 60V at extra charge. However, the specified currents must not be exceeded.
Delivery time on requestk
Three-phase DC power supply RDRKL 10-120 (K)
THREE-PHASE DC POWER SUPPLYRDRKL 10 – 120Three-phase compact rectifier transformersStandard version:with a downstream three-phase bridge rectifier,Input 3AC 380/400/420V, output DC 24V, residual ripple < 5%Capacitor design:with a downstream three-phase bridge rectifier and capacitor,Input 3AC 380/400/420V, output DC 24V, residual ripple < 2% General:Like the RDRK series, the RDRKL series has been specifically developed for use with programmable logic controllers (PLCs). The transformers are very well-dimensioned and voltage-stable. This results in a particularly flat characteristic curve between no-load and load conditions, ensuring that overvoltages or undervoltages critical for PLCs do not occur, even during significant mains fluctuations.The rectifiers are protected against short-term current surges and voltage spikes.The protective circuitry for the capacitor version is provided by a protective circuit board containing the corresponding varistor, foil capacitor, and discharge resistor.Configuration:Open, horizontal design, stationary, for equipment installation and mounting in dry rooms, separate windings, all connections via creepage-current-safe screw terminal blocks. The terminals are protected against contact by the back of the hand and fingers in accordance with UVV (BGV A3).IP 00, insulation class E, max. ambient temperature 40°C (ta40°C/E)For versions with a capacitor, the dimensions change slightly. The mounting dimensions remain unchanged.Other versions available upon request (fuses, voltages, connections, etc.) Insulation class E
Delivery time on requestk
Single-phase DC power supply GGT 100 – 630 230V
Single-phase DC power supplyGGT 100 – 630Single-phase compact rectifier transformersInput AC 220/230/240V or AC 380/400/420VOutput DC 24V, residual ripple 48%. New series with higher current with downstream rectifier, varistor, and discharge resistor Residual ripple 48%, retrofitting a capacitor is not possible. Same design as above. The EN 61000-3-2 harmonic standard is complied with. IP 00, suitable for installation up to protection class IP 23, insulation class E, max. ambient temp. ta 40°C insulation class E
Delivery time on requestk
Three-phase DC power supply RDRKS 7.5-30 (K)
THREE-PHASE DC POWER SUPPLYRDRKS 7.5 – 30Three-phase compact rectifier transformersStandard version:with a downstream three-phase bridge rectifier,Input 3AC 380/400/420V, output DC 24V, residual ripple < 5%Capacitor design:with a downstream three-phase bridge rectifier and capacitorInput 3AC 380/400/420V, output DC 24V, residual ripple < 2% General:The RDRKS series, featuring a modern industrial design, was developed with the following considerations in mind: Optimized design, resulting in a small footprint Easy installation thanks to the open slot Compact design with low weight High reliability and long service life Excellent value for money Low total lossesConfiguration:Enclosed design, stationary, for equipment installation and mounting in dry rooms, separate windings, mounting via an open slot integrated into the cover. Connection to transformer terminals with screw terminals that are protected against leakage current. The terminals are protected against contact by the back of the hand and fingers in accordance with UVV (BGV A3).IP 00, insulation class E, maximum ambient temperature 40°C (ta40°C/E).Other voltages available upon request.
Delivery time on requestk
Single-phase DC power supply REP1-2403 115 ... 230V
Single-phase DC power supplyREP1 72 – REP3 600Regulated primary-switched single-phase switching power suppliesAvailable in 40-70W, 95-120W, 120-180W, 240-336W and 480-600WInput wide input voltage range AC 90-264V, AC 90-135V and 180-264V, AC 187-264V and 330-550V, 3AC 330-550V (depending on version) see data sheetOutput DC 12, 24 or 48V (depending on version) see data sheet General:The REP power supplies are high-quality switching power supplies for DIN rail mounting. They stand out thanks to their compact and intelligent design as well as their robust metal housing.The output voltage is easily and simply adjustable (DC 22V to DC 27V) and remains highly stable even with temperature fluctuations and load changes. In addition to short-circuit protection with 3 different output protection modes, overload and overvoltage protection at the output ensure a high level of safety.Special features of the REP series The output power can be easily increased by connecting additional REP power supplies of the same type in parallel (max. 4 units/280-500W version) Series connection possible up to DC 110V 1.5 times the rated current for 3 min. 3 times the rated current for 300ms.Alternatives:The devices of the REP series are also available in DC 12V as typeREP1-1206 (Secondary DC 12V/6A) Part No.: 0540-00001206REP1-1214 (Secondary DC 12V/14A) Part No.: 0540-00001214The devices of the REP series are also available in DC 48V as typeREP1-483.75 (Secondary DC 48V/3.75A) Part No.: 0540-00483.75REP1-4807 (Secondary DC 48V/7A) Part No.: 0540-00004807REP1-4812.5 (Secondary DC 48V/12.5A) Part No.: 0540-00004812.5No UL certification for DC 12V and DC 48V versionsFor more information, see www.riedel-trafobau.de
Delivery time on requestk
Do you have specific requirements?
We’ll provide you with personalized advice and work with you to find the right solution for your application.